RSpice

RSPICE / DOCS / SCHEMATIC ENTRY

Schematic entry.

Draw a circuit in the Design workspace: place parts, wire them, name nets, build hierarchy and symbols, and check the result before you simulate it.

WORKSPACE
Design, Alt+2
PARTS
Component shelf or Design › Place
CHECK
Design › Check cellview, Ctrl+E
CANCEL
Escape ends the active tool

01 / THE DESIGN WORKSPACE

The drawing, the navigator and the shelf.

The Design workspace (Alt+2) shows the open cell view: a schematic, a symbol, or a Verilog-A source. Its side panel has two tabs: Navigator, for the design in front of you, and Component shelf, for the parts you can add to it.

Single-letter keys such as W or R act while the drawing has keyboard focus, and not while you type in a field. Preferences › Shortcuts can require Alt with them, turn them off, or change any key. The keys below are the same on the desktop and in the browser unless the text says otherwise.

02 / PLACE PARTS

From the shelf or the Place menu.

In the Component shelf, click a part to arm it, or drag it onto the sheet. The built-in parts are grouped as Passives, Sources, Analog, and Mixed signal / XSPICE. Design › Place arms the common parts and drawing objects by key, and Place › Instance… (Shift+I) places a cell from a library.

PLACEKEYPLACEKEY
ResistorRVoltage sourceV
CapacitorCCurrent sourceI
InductorLGroundShift+G
DiodeDInstance…Shift+I
Text or note…Shift+TDocumentation shape…—

Edit › Paste (Ctrl+V) and Edit › Duplicate (Ctrl+D) float the copy under the pointer until you click to place it: R rotates it, M mirrors it and Escape lets it go. Edit › Repeat last command (.) runs the last placement or editing command again, as it last ran.

03 / WIRES AND NETS

Connect, name and inspect nets.

DESIGN › PLACEKEYUSE
WireWDraw a wire between terminals.
Net labelNName a net; wires carrying the same name are connected.
JunctionJMark a connection where wires cross.
BusBDraw a bus.
Bus tapTTake one member off a bus.
Off-sheet connector—Carry a net to another sheet.
Pins…Shift+PPlace the cell's interface pins.

Design › Highlight net lights the net the selection is on. Design › Connectivity and buses… reviews connectivity, typed buses and global nets, and Design › Arrange › Join collinear wires merges wires that run on one line into one wire each.

04 / EDIT AND ARRANGE

Select, change and line up.

  • Move (M) moves the selection; Stretch (S) moves a selected wire segment, or a shape's control point, and the wires joined to it follow.
  • Properties… (Q) edits the selected object's values; Rename… (F2) renames it.
  • Design › Arrange: Rotate clockwise (Ctrl+R), Rotate counter-clockwise (Ctrl+Shift+R), Mirror about vertical axis (Ctrl+M), Mirror about horizontal axis (Ctrl+Shift+M), the Align and Distribute commands, and Snap selection to grid.
  • Edit › Select selects every Instance, Wire, Net label, Pin, Text or Shape on the active sheet. Edit › Find… (Ctrl+F) searches the design; Find and replace… (Ctrl+H) has that key on the desktop only.
  • Replace instance…, Create array… and Bulk edit… in the Edit menu change many objects in one step. Design › Annotate reference designators… assigns reference designators, and Design › Object table… (Ctrl+Shift+T, desktop) lists objects in a table.

05 / ZOOM AND GRID

Move around the sheet.

VIEWKEYVIEWKEY
Zoom in+Zoom out−
Fit drawing sheetFFit contentShift+F
Zoom boxZZoom previousShift+W
Zoom 100%Ctrl+0 desktopZoom to selection—

View › Grid shows the grid as Dots, Lines or Off; Grid, snap and routing… sets the grid pitch, what the pointer snaps to, and how wires route.

06 / HIERARCHY AND SYMBOLS

Cells inside cells.

  • Design › Descend (Shift+E) opens the selected instance's cell, following your edit-in-place preference. Descend with options… (H) lets you choose the edit mode: edit in place, open an isolated cell view, open a read-only reference, or edit its symbol in place. Return to parent (Shift+H) goes back up.
  • Create symbol from schematic… makes a symbol for the open schematic's cell from its pins, so the cell can be placed as an instance elsewhere.
  • Create hierarchy… turns the selection into a new child cell with a generated symbol.
  • Edit symbol in place edits the selected instance's symbol where it stands on its parent schematic; in the symbol view, Return to parent schematic (Enter) goes back.
  • In a symbol view the Place menu holds drawing tools instead: Pin (P), Line (L), Rectangle (R), Circle (C), Arc (A), Polygon (G) and Text (T). Validate and save symbol checks the symbol's pins against the cell's interface and saves it.

07 / SHEETS

Multi-sheet schematics.

Design › Sheet moves between sheets with Previous sheet (PageUp) and Next sheet (PageDown), adds one with New sheet, and removes one with Delete…. Sheet properties (Ctrl+Alt+Shift+P) shows the open sheet's properties in the inspector; Sheet formats… and Sheet defaults… manage the formats and the defaults new sheets take.

08 / CHECK THE DESIGN

Find connection and rule problems before a run.

DESIGN MENUKEYCHECKS
Check cellviewCtrl+EThe open cell view only. A symbol view checks its pins against the cell's interface.
Check design—The whole design from the simulation root, plus every cell view in the project's own libraries that the walk does not reach.
Check and save…Ctrl+Shift+EChecks, then saves a validated revision.
Violations › Next violation] or F8Steps to the next finding; Previous violation is [ or Shift+F8.

Violations › Clear check results clears the findings. Design rule setup… sets the severity each rule is reported at in this project. Findings also appear in View › Problems.

09 / PRINT AND EXPORT

Get the drawing out.

File › Print… (Ctrl+P; Ctrl+Alt+P in the browser) prints the active view. File › Export › Image or PDF… (Ctrl+Alt+Shift+E) writes it as PDF, PDF/A, SVG, PNG or TIFF. Edit › Copy as image puts the selection, or the whole view, on the clipboard as a picture. To simulate the circuit, go on to Simulation setup.